Find

  • All tenders
Finland: Tenders/Aalto-korkeakoulusäätiö sr/Electrochemical atomic force microscopy device

Electrochemical atomic force microscopy device

Awarded

The competition has ended and a winner has been selected.

Award
Procedure
Without prior noticeTwo stages
Agreement
Buying goods

Brief

Aalto University Foundation sr has entered into an agreement with BSL Vetenskaplig filial to supply an electrochemical atomic force microscopy device for Helsinki-Uusimaa, Finland, for a total contract value of €369,405. The system must provide non-resonant sinusoidal-oscillating imaging with real-time contact-force measurement and automatic feedback optimisation, temperature control, low z-noise and a closed-loop scanner, as well as extensive imaging and spectroscopy capabilities including PFM, torsional resonance and KPFM. It must also accommodate additional components, include a motorised programmable sample stage with vacuum hold-down, and provide automated tip engagement. One bid was received.

Laboratorie- og analyseutstyr

Result

TED
  • BSL Vetenskaplig filial
    Winner
  • Number of tenders received
    1
  • Contract value
    €369,405

Previous winners

  • Who are you up against?

    The suppliers who have won similar contracts at Aalto-korkeakoulusäätiö sr

Will you bid?

The agent sets up the bid and writes the first draft. Free for 14 days.

Award Criteria

  • Description

    Price

    Source

    No source found in the documents. Check the weight against the tender documents.

From the notice

  • Electrochemical atomic force microscopy device: 1) non-resonant sinusoidal-oscillating imaging mode (nroIM): a. Pure vertical z-modulation of the cantilever; amplitudes (from < 1 nm to > 250 nm) and frequencies (from 125 Hz up to 2 kHz) freely selectable. b. In each contacting cycle, a direct determination of the maximum contact force (force setpoint) takes place in real time, where upon all control parameters are automatically and continuously optimized. Force setpoint minimum down to 10 pN. Stable imaging also for "negative force setpoints", i.e., below the baseline of the free force curve. c. Effective line rate >= 2 Hz at 512 pixel/line for all force setpoints possible. d. Suited for cantilevers with spring constants from < 0.001 N/m to > 500 N/m. e. Topography, DMT modulus, adhesion, energy dissipation, force setpoint error and deformation are measured and displayed simultaneously (location and time) and in real time. f. Lateral resolution down to atomic defects in lattice is possible. g. The tip-sample force interaction is continuously displayed in real time during the imaging process. h. This mode can be operated without any limitation of functionality with liquid cells, heating cells, EC cell, etc. The change of deflection signal due to cantilever drift is automatically and continuously eliminated (drift, e.g., induced by change of temperature or other environmental conditions). 2) System should be temperature controlled to minimize thermal drift: sensor in scanner and bridge with feedback loop to have scanner + bridge at similar temperature. Availability to heat from ambient to 35 deg. C. 3) System must be: a. Low-z-noise (< / = 40 pm RMS) atomic force microscope (AFM) with closed-loop tip-scanner (in all 3 axes) >= 85 um x 85 um x 9.5 um XYZ. b. Large sample space, capable to integrate heavy (> 5 kg) additional components (e.g., Nanoprober, customized sample holders, external magnetic fields). c. Motorized 150 mm x 150 mm sample stage. d. Extensive set of resonant, non-resonant and non-resonant oscillating imaging modes. The non-resonant, sinusoidal-oscillating imaging mode (nroIM) with freely selectable i) pure vertical z-modulation of the cantilever (amplitudes from < 1 nm to > 250 nm) and ii) frequencies from 125 Hz up to 2 kHz, WITH automated, continuous contact force dependent imaging gains optimization. e. Enhanced scan parameter optimization algorithms that continuously monitor and automatically optimize key feedback-loop parameters (gains, setpoint) for all 3 imaging modes (contact, resonant and non-resonant oscillating). Algorithms are also based on a trace-retrace correlation score. User sets scan size, scan rate and pixel density, then selects engage and system sets and automatically controls feedback settings during scanning continuously. f. Extensive set of piezo force microscopy (PFM) imaging and spectroscopy modes volume spectroscopy (hyperspectral mapping modes) of PFM signals (frequency sweep on large bandwidth to get contact resonance frequency and eigenmode (amplitude/phase versus voltage) simultaneously to topography and mechanical properties, further referred to as dataCUBE modes. g. Torsional resonance mode to acquire dynamic friction signal. Mode has proven to high-resolution image moire pattern of stacked 2D materials. h. Nano-electrical imaging of surface potential (KPFM) in non-resonant, sinusoidal-oscillating imaging mode. 4) Sample handling and automation: a. Accessible sample space >/= 150 mm x 150 mm x 18 mm XYZ, up to 45 mm height. b. Motorized (minimum 150 mm x 150 mm) and programable sample stage, with vacuum sample hold down. c. Vertical, software controlled and automated AFM-tip engage functionality.

  • Contact

    Marius Reuringsmarius.reurings@aalto.fi
  • Type
    Result · Prequalification
  • Location
    Helsinki-Uusimaa
  • Main code
    Laboratory, optical and precision equipments (excl. glasses)
    38000000
  • 38510000Microscopes38514000Darkfield and scanning probe microscopes38514200Scanning probe microscopes

Similar active competitions

  • Fundació Institut Català de Nanociència i Nanotecnologia (ICN2)

    Laboratorie- og analyseutstyr

    SUMINISTRO, INSTALACIÓN Y PUESTA EN MARCHA DE UN SISTEMA DE MICROSCOPÍA DE FUERZA ATÓMICA CON CARGA AUTOMATIZADA, INTEGRADO EN UNA CAJA DE GUANTES Y APTO PARA LA MEDIDA DEL POTENCIAL DE SUPERFICIE, DESTINADO AL INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA (ICN2)

    La Fundació Institut Català de Nanociència i Nanotecnologia (ICN2) necesita el suministro, entrega, instalación y puesta en marcha, en sus instalaciones de Barcelona, de un sistema de microscopía de fuerza atómica con carga automatizada, integrado en una caja de guantes adaptada y apto para medir el potencial de superficie. El equipo deberá funcionar en un ambiente controlado y con luz de longitud de onda superior a 630 nm; el plazo de ejecución es de 4 meses.

    Competition
    Dec 16, 2026(23 days)
  • Freistaat Bayern, vertreten durch die Universität Bayreuth

    Laboratorie-, optisk- og presisjonsutstyr

    Höchstauflösendes Rasterkraftmikroskop (AFM)

    Der Freistaat Bayern, vertreten durch die Universität Bayreuth, benötigt ein hochauflösendes Rasterkraftmikroskop (AFM) einschließlich aller für den Betrieb erforderlichen Hard- und Softwarekomponenten zur Charakterisierung von Oberflächen und Grenzflächen auf Nano- und atomarer Skala. Das System soll insbesondere 3D-AFM-Messungen in Flüssigkeiten und driftarme Langzeitmessungen für Forschungsanwendungen ermöglichen und nach Bayreuth geliefert werden. Die Angebote werden zu gleichen Teilen nach Preis (50 %) und Qualität (50 %) bewertet.

    Competition
    Nov 27, 2026(4 days)
  • Universidade de Santiago de Compostela

    Laboratorie-, optisk- og presisjonsutstyr

    022N-26 Adquisición de un sistema de microscopía de sonda de barrido

    La Universidade de Santiago de Compostela está planificando la adquisición de un sistema de microscopía de sonda de barrido criogénico, que incluye un criostato de helio líquido y una punta SPM de siete contactos, para realizar mediciones en modos de microscopía de fuerza atómica sin contacto (nc-AFM) y microscopía de efecto túnel (STM), así como sus variantes espectroscópicas. Se trata de un suministro de bienes.

    Planning